For many, drywall is the material of choice when building even, smooth walls. It’s adaptable, simple to install, and offers the ideal foundation for a range of finishes. But before applying wallpaper, paint, or any other kind of finish, the surface must be properly prepared for a flawless appearance.
Putty is one of the most crucial steps in this procedure. Putty can be used to smooth out drywall imperfections, cover screw holes, and fill in seams. This guarantees that the finish you’ve selected will look polished and tidy.
We’ll walk you through every step of puttying drywall in this post, from selecting the appropriate supplies to actually applying the putty. Whether you want to paint, apply wallpaper, or use another finish, following these suggestions will help you get the greatest outcome.
- Rules for putting putty
- How to prepare the surface for puttying
- How to putty drywall corners
- Pickwall putty for wallpaper gluing
- Video on the topic
- How to Prepare DRYWALL for Decorative Plaster? How to Seal JOINTS?
- Sealing four types of drywall seams
- Puttying drywall walls. HOW TO KEEP CALM? Puttying joints, corners and more.
- How to putty Drywall under wallpaper, painting. Is starting putty necessary?
Rules for putting putty
You will then be given instructions on how to complete this task. As soon as you look at the picture, you can tell how much work is involved. Each base plane material will require its own preparation, after all. Be patient and careful to complete everything.
How to prepare the surface for puttying
You must choose the kind of surface, the gypsum fiber, the producer of these materials, and many other factors before you begin puttying the surface. Ideally, the surface should be smooth:
- Before you start puttying the gypsum board, you need to process everything and properly prepare it. The surface should be carefully examined not only from the outside, but also from the inside. Even screws are important. A spatula can be a good reference point for analysis.
- Take the spatula in your hand and run it over the surface. If it does not touch the screws, then everything is fine, the surface is quite smooth and ready for puttying. If the spatula starts to “catch” the screws, then they need to be screwed in tightly.
- The screws should be “sunk” as deep as possible. It also happens that the screws are screwed in too deep – here, too, you will have to work. You need to unscrew them and putty the “holes”. Otherwise, the wallpaper (see.Finishing drywall for wallpaper: doing it right) will fall off or lie unevenly.
Note: You cannot screw in additional screws in the same locations if new ones need to be installed. After taking a one-centimeter step back from the holes, you must connect.
- Before puttying the surface, it must be properly cleaned. Take a rag and remove dust, dirt, debris, chips. To prepare the surface in the best possible way, you will need a primer. In this case, the adhesive properties increase, the surface adheres well to the putty.
Note: Keep in mind that the primer needs time to dry after application. It will require multiple days to complete! You can only move on to the next phase of preparation after this.
- In places where sheets are joined and where screws are screwed in, you will need to glue a special reinforcing mesh. Then the putty will not crack or fall off.
How to putty drywall corners
Before you start working, you need to become an expert in the technology. Every seam and joint needs to be carefully processed. This will shield the material from damage and cracking. Understanding the technology behind plasterboard corner puttying is crucial. If not, you will receive something that is entirely unrelated to your original request. The following are the general guidelines for working with drywall. Thus:
- It is important to remember that this material is very fragile. One careless movement, and you can damage the surface.
For proper processing of drywall corners, plastic or metal corners are usually purchased (see.Perforated corner for putty – which one to choose and how to attach). They are sold in any construction or hardware store. Such parts help to smooth out sharp corners and protect them from damage. - On both sides of the joint, you need to apply an impressive layer of putty and carefully press it into the corner. It is important to prepare the corner itself in advance.
Excess putty must be removed, then apply another layer. The finishing layer will not be very thick, it is important to level it well. Then the putty should dry well.
- If after the work done you are not satisfied with the result, then you can apply another layer of putty. It will be called “zero”.
Keep in mind that leveling everything out is crucial! The inner corners will be simpler to putty than the outer ones. You’ll need serpyanka for this.
Pickwall putty for wallpaper gluing
It is crucial to apply surface preparation carefully and accurately so that the final appearance of the walls or ceilings pleases you after all the work is completed. The preparation you do before adhering roll wallpaper will not be the same as what you do otherwise. Thus:
- If the wallpaper is thick, heavy, then the putty mixture should be appropriate. Choose coarse -grain options.
Then the surface will not be smooth, but slightly ribbed. This will greatly facilitate the future worship of wallpaper. The finish putty in this case will not be needed, but you need to level flaws on the sheets of drywall! - If you are going to glue paper about (they usually have a thin structure), then to putty will appear. All the irregularities of drywall will immediately get out.
In order to prevent this from happening, use the finish option immediately. Its granular structure will give a smooth surface in the end.
- Some “masters” prefer to putty only the joints of the drywall sheets. Don’t do this! The entire surface must be putty.
Otherwise, in the future, after the wallpaper is pasted, all the flaws will come out. Putty joints will be very visible, both in daylight and in artificial light. The middle of the sheets that have not been puttyed will also be noticeable!
The right use of putty is crucial for achieving a flawless finish when installing wallpaper or other coverings on drywall. This procedure ensures a clean, polished appearance by smoothing out flaws and priming the surface. Even a novice can successfully putty drywall by following a few simple steps, which will create the ideal base for any wall finish.
Step | Description |
Preparation | Clean the drywall surface, remove dust, and apply a primer to ensure better adhesion of the putty. |
First Layer | Apply a thin layer of putty to fill joints and cover screws. Let it dry completely. |
Sanding | Once the first layer is dry, sand the surface lightly to remove any rough spots. |
Second Layer | Apply a second, smoother layer of putty over the entire surface for an even finish. |
Final Sanding | After the second layer dries, sand the surface again to achieve a smooth, flat finish. |
Final Check | Inspect the surface for imperfections, and if needed, apply a final thin layer and sand once more. |
Ready for Finishing | Your drywall is now ready for wallpaper or any other type of finishing. |
Installing drywall is an essential step in getting a polished and seamless finish, regardless of whether you want to use wallpaper or another kind of ornamental covering. You can build a strong base that will support your walls and look fantastic for years to come if you take the correct procedures.
Recall that the details are crucial. Sanding, priming, and joint compounding should be done slowly. Although these procedures may seem laborious, they are necessary to prevent flaws from showing through your finish.
Installing drywall beneath wallpaper or other finishes isn’t as difficult as it might seem once you’ve mastered the technique. Whatever finish you decide on, your walls will be ready to shine with a little perseverance and attention to detail.