How to make textured plaster from ordinary putty

Redesigning the appearance of your walls doesn’t always need costly supplies or expert knowledge. Ordinary putty can be transformed into lovely textured plaster that gives depth and character to any space with a little imagination and perseverance.

With this method, you can create a range of finishes, from delicate patterns to striking designs. A steady hand, a few basic tools, and an openness to trying new things are all you need. What was the outcome? a distinctive, handmade appearance that exudes timelessness and modernity.

This post will walk you through the easy steps of making textured plaster with regular putty, allowing you to give your house a unique touch.

Step Description
1. Surface Preparation Clean and prime the wall to ensure good adhesion.
2. Mix the Putty Prepare the putty by mixing it according to the instructions on the packaging.
3. Apply the Base Layer Spread a thin, even layer of putty on the wall using a trowel.
4. Create Texture Use tools like a brush, sponge, or trowel to create the desired texture while the putty is still wet.
5. Let it Dry Allow the textured layer to dry completely before proceeding.
6. Sand the Surface If needed, lightly sand the surface to remove any rough edges.
7. Paint or Seal Apply paint or sealant to protect the textured surface and enhance its appearance.

Preparatory stage

You must treat the surface, which will act as a test bed for the mixture when applied, before making the mixture with your hands. This is a crucial step that needs to be completed with extreme caution. The outcome will not be at all what you had hoped for if you ignore this. What actions are necessary?

    The surface on which the composition will be applied must be cleaned of the coating that was there before. If the wall was covered with wallpaper, then it must be completely removed. The existing layer of plaster must be checked for strength. If there are voids between it and the base of the wall, then this is an alarming sign. If it is clear that collapse cannot be avoided, you will have to dismantle the layer and do it again.

Tip 1: Use water to remove any wallpaper with your hands, even the ones that are too heavy to be lifted with a spatula. Pour it into a spray bottle and use it to moisten the wallpapered area. You’re even more proficient at it. There’s no need to take down the dry wallpaper. Just thoroughly wet them and let them sit for roughly five minutes will do. Following that, tape will be used to remove them.

Tip 2: You can attempt a manual repair if spaces were discovered between the "rough" layer of plaster and the wall’s base. Use a big drill to drill holes in the spaces to accomplish this. They should be separated by ten to fifteen centimeters. Thoroughly pour the prepared liquid plaster solution into the holes.

VIDEO: Applying texture to walls using your hands

Tools

You must set up the tools and the surface before beginning any work. Then, you can’t get sidetracked from finding the ideal item. You’ll require:

  • Two plastic buckets. The solution will be prepared in one, the other for water.
  • A screwdriver or drill. Also a mixer attachment.
  • A special metal trowel, which will create a unique texture.
  • Trowel. It is needed for applying the solution.
  • Spatulas. It is better to choose several sizes.
  • Level.
  • Abrasive mesh and construction tape.
  • Pencil and ruler.
  • Ordinary polyethylene film (bag).
  • Brushes and roller, container for paint.

After completing the preparatory steps, all that’s left to do is measure the surface area with your hands to determine how much putty will be needed for the job. The only challenge you might face is deciding which combination to use. Putty comes in two primary varieties: cement and gypsum. They are ready-made or dry-made. Although the latter is substantially more expensive, it is far more convenient.

How different textures are created

There are several techniques you can employ to create a texture with your hands. Everything is entirely dependent on the type of structure you are looking for. They are incredibly numerous. We shall examine the most well-liked ones below.

Recall that the success of decorative plaster depends on adding the right texture. It’s not necessary to count on things going perfectly the first time. Thus, it is advised to get some practice. It will seem difficult at first, but as soon as you learn how to move the trowel, spatula, or brush, it will become easier. In any case, there’s no cause for concern. Nevertheless, you will have a unique piece that you made yourself.

Scales

The layer of putty that is applied to the wall should not be thicker than five millimeters. Movements are made from top to bottom and backwards with a spatula. The entire surface starts to resemble scales. The strokes must be more frequent the thicker the putty layer.

Cave

Putty is quickly sprayed over the whole surface. Here’s where polyethylene film comes in handy. It must be applied and gently pressed onto the damp surface. Everywhere around the perimeter, this has to be completed promptly. On the wall, a pattern that resembles a stone surface will develop.

Rocks

A trowel will be required. Similar to the earlier situations, a plastic solution must be used. Use a trowel to scrape the surface; an angle is preferable. This ought to be carried out haphazardly, but without making sudden direction changes. You’ll receive a simulation of fractures in rocks.

Such common textures can be made by anyone. Generally speaking, it’s best to use your imagination. You can use a variety of materials and tools in this situation. Getting a distinctive drawing that appeals to the eye is what matters most.

Final stage

Once the putty is totally dry, you can start the last step. Specifically, painting. You can use multiple shades that will overlap to achieve a more dramatic effect. This contrast will enhance the surface’s elegance and give it a distinctive appearance.

Paint is usually chosen on its own and doesn’t require any special explanation. However, priming the decorative putty is the most important step. Paint can be applied in various ways, and the texture can be further enhanced by using different application methods.

Using regular putty to create textured plaster is an inventive and useful way to give your walls personality. You can turn plain surfaces into eye-catching designs that fit your style with a few simple tools and techniques.

Various techniques such as troweling, brushing, or sponging can be used to create a range of textures that resemble more expensive materials. This allows you to personalize the style to suit your space while also saving money.

Before applying paint or sealer, make sure your walls are properly prepared, that the putty is applied evenly, and that it has had time to completely dry. You can add a distinctive, personalized touch to your walls that will make them stand out with a little perseverance and work.

Using regular putty to create textured plaster is an easy and affordable way to give your walls more visual appeal. You can customize your wall finish to match your style by using basic tools and techniques to turn plain putty into a variety of textures. Compared to purchasing specialty plaster, this method not only saves money but also offers you more artistic control over the finished appearance.

Video on the topic

Do-it-yourself decorative plaster from ordinary putty

Do-it-yourself grotto made from ordinary putty

Super loft, made from ordinary putty. Texture of a fur coat. #loft #decorativeplaster #doityourself

5 best ways to make decorative plaster with your own hands from ordinary putty

The simplest decorative plaster with your own hands.From ordinary putty.

What interior style do you like the most?
Share to friends
Dmitry Stepanov

Professional decorator with 10 years of experience. I know everything about renovating apartments, houses and offices. I will be happy to share my knowledge and experience with you.

Rate author
Vash-Variant.com
Add a comment