How to glue wallpaper on chipboard, fiberboard, MDF: nuances and technology

It can be difficult to apply wallpaper glue, particularly if the walls aren’t constructed of conventional materials like drywall or plaster. Working with surfaces like MDF, chipboard, or fiberboard necessitates a little more attention to detail in the procedure. These materials present some special difficulties, but with the appropriate method, a stunning and durable finish can be obtained.

Before beginning, it’s critical to comprehend the nature of these materials. Chipboard, fiberboard, and MDF, in contrast to smoother surfaces, can absorb moisture and adhesive in different ways, which influences the wallpaper’s adhesion. It is essential to properly prepare the surface in order to avoid problems such as peeling or bubbling later.

We’ll guide you through the procedures in this post to make sure your wallpapering job on these surfaces goes without a hitch. From surface preparation to wallpaper application, we’ll go over the key methods and advice you should be aware of. You’ll find the advice you need to achieve results that look professional, whether you’re a do-it-yourself enthusiast or simply looking to update a space.

Is it possible to glue wallpaper onto wood boards??

On this matter, there are two different points of view. While one of the craftsmen claims that performing such internal work is completely impossible, the other says otherwise.

The truth is that glue is typically applied to non-woven, vinyl, and paper products without adequate surface preparation. Usually, all that needs to be done is scrape off the old coating. However, this is the case with plaster-finished walls, which guarantees the required material adhesion. Issues arise if the work is done on a foundation of wood boards (chip and fiber). This is, first and foremost, the subsequent stripping at joints and in corners. Poor surface preparation, which takes a lot more time and effort, is the cause of these defects.

It is true that adhering wallpaper to fiberboard, chipboard, and MDF is difficult, but if all steps are followed precisely and methodically, the integrity of the coating will be guaranteed.

Why do you need putty?

If you wish to install high-quality roll products on the walls, you must use this composition. It carries out the subsequent tasks:

1. Creating the necessary adhesion. In the production of wood boards, various resins are used that ensure the unity of the canvas, but prevent the wallpaper from sticking.
2. Protection of the base. Due to the porosity of the material (especially untreated chipboard), the glue is quickly absorbed without creating a binding film, so the application has to be repeated many times. Using a water-based composition can lead to deformation of the surface.
3. Alignment of the coating. For lining vertical structures, panels of not the highest class are used, and puttying allows you to eliminate existing defects (depressions, chips, scratches).

Stains that may develop on the decorative layer as a result of the resins in the sheet present another serious issue. They detract from the walls’ appearance and still show after a considerable amount of time.

Because chipboard, fiberboard, and MDF have distinct surfaces that can be challenging to work with, careful preparation is necessary to ensure a smooth, durable finish when adhering wallpaper to these materials. Achieving a professional look requires knowing the proper methods and paying close attention to details like priming, sealing, and selecting the right adhesive. You can successfully wallpaper these difficult surfaces by following this guide, which will walk you through the nuances and technology involved.

Technology for pasting roll products

Wood boards can only be wallpapered using your hands. You have to follow the steps carefully in order for all procedures to be completed correctly.

Materials and tools

To perform pasting tasks, you will require the following supplies and equipment:

• Primer. It is necessary to choose a composition with deep penetration. The best option is polymer mixtures. You can also use "betonokontakt".
• Wallpaper. The variety is selected based on the wishes and style of the room. You should refuse single-layer paper products.
• Glue. For each type of material, there is a special composition.
• Putty. It is recommended to purchase acrylic or oil-based putty for chipboard, which has elasticity. This is especially true for newly built houses. Ready-made solutions are preferable.
• Serpyanka mesh. Needed for reinforcing the joints of the slabs.
• Brushes and roller. Several types and replaceable attachments should be provided for applying the primer and glue.
• A set of spatulas. Small, medium and wide tools will be required.
• Containers for mixing solutions.
• Devices for smoothing the wallpaper.

Everything that you require is pre-purchased. If used, the tools are already cleaned from earlier materials.

Surface preparation

The process of adhering roll products to various panels may differ slightly, so it is important to start with the particular circumstance. A variety of specific procedures are involved in preliminary work for each type:

1. Chipboard. Such a base needs to be sanded. The fact is that the upper structure is not always uniform, particles can peel off. So that they do not interfere with work in the future, they are removed with sandpaper.
2. DVP. Gluing wallpaper on wood -fiber slabs is much more difficult. This is due to the fact that the front side of the organ is saturated with the composition of paraffin to increase moisture resistance. When gluing decorative products, this creates difficulties, so the slabs are treated with a grinding machine, evenly removing a very thin layer.
3. Chipper. The laminated coating also complicates the clutch, so this surface is thoroughly polished – as in the previous version – until the rough base is obtained.
4. MDF. To glue wallpaper on the MDF panels, you will need to perform similar procedures, but carefully: the surface needs only light grinding.

General procedures to be followed after preliminary work is finished:

• Padding. The surface with a roller is covered with two layers of the composition, each is dried.
• Sealing seams. When working with fiberboard, the edges of adjacent ends are cut at an angle with a construction knife. Chipboard walls are not subject to pointing. Then the seams are filled, the excess is removed.
• Laying the serpyanka. It covers the front and corner joints (there is a special variety), a thin layer of the mixture is applied on top, completely covering the reinforcing mesh.
• Puttying. The base should be puttyed as follows: the solution is collected on the blade of a wide spatula and distributed over the surface with arcuate movements from top to bottom. The procedure is repeated, after which the coating is primed.

It is left to dry completely on the walls.

If there are any deviations in the vertical structure, it is recommended that the final layer of putty be applied after plastering the surface.

Paping

The first step in the process is to evaluate the putty’s adherence by lightly tapping the surface. If there isn’t any delamination, carry out the following steps:

1. Pre-prepare the place for work, remove all unnecessary. The wallpaper should be cut to fit the pattern.
2. It is recommended to start gluing from the window opening. The first strip is carefully measured, since the remaining fragments are oriented to it.
3. The glue is evenly applied to the back of the wallpaper, after which the sheets are folded in half. This will prevent drying and ensure the desired level of impregnation. If necessary, the wall is also treated with the solution.
4. The strip is laid in its place, adjusted from above and pressed. A rag or rubber spatula is used for smoothing.
5. The remaining elements are glued in a similar way.

It is suggested that varnish be applied to the surfaces. Yes, this can be done, but it won’t be easy to get the desired ornamental effect. Furthermore, the front layer will thicken and may begin to peel.

You should know this! If the strips are joined end to end, it is recommended to use a special intermediate tape.

While wallpapering chipboard, fiberboard, or MDF surfaces may appear difficult, it is possible to achieve success with the correct planning and methods. You can accomplish a smooth, durable finish by taking the time to appropriately prepare the surface and select the adhesive.

To ensure that the wallpaper adheres well, don’t forget to prime and clean the surface. A successful project depends on choosing the correct wallpaper type and applying the proper gluing technique.

Even on these difficult surfaces, you can update your decor and enjoy the new look that wallpaper provides by paying close attention to these details.

Video on the topic

How to glue wallpaper on chipboard preparatory work and necessary materials and tools

Rules for gluing wallpaper on chipboard

Wallpaper on the 2nd floor #1

gluing wallpaper on OSB