Concrete can have bare walls transformed into chic and inviting spaces by applying non-woven wallpaper. Even though it may seem difficult, completing the task correctly makes it much simpler to achieve a polished appearance.
It’s important to prepare properly whether you’re working with freshly laid concrete or renovating an old wall. You can guarantee that your wallpaper will adhere smoothly and last for years by properly prepping the surface and selecting the appropriate tools and materials.
We’ll take you step-by-step through the entire process in this guide, from prepping the concrete wall to confidently hanging the wallpaper. You can have a gorgeously decorated wall that gives your house warmth and character if you take the proper approach.
Rules for gluing non-woven wallpaper on concrete
A specific order should be followed when adhering non-woven wallpaper to concrete. Let’s decide what to do and how to do it right away.
Note: You must use top-notch supplies to complete the task. Give reputable manufacturers precedence. Additionally, avoid purchasing glue from street vendors in the winter. Its binding qualities are lost when it freezes.
The following is the order in which the work will be completed:
| Preparation of the plane | At this stage, we need to create a flat base. Otherwise, the coating will repeat the uneven relief and the design will already be spoiled. |
| Preparation of glue | This is done in advance. The glue must be infused and then brought to a homogeneous mass. |
| Pasting process | At this stage, we need to prepare the wallpaper itself, and the devices that will be used to do the work. This is especially important for various transitions and for hard-to-reach places. |
Everything is now detailed and in order.
Prior to applying non-woven wallpaper adhesively to concrete, make sure the surface is dry, clean, and smooth. To improve wallpaper adhesion, prime the concrete and cut the wallpaper into strips, leaving extra for trimming at the top and bottom. Apply adhesive to the wall using a roller, not the wallpaper, and then gently lay each strip onto the adhesive, using a brush or sponge to smooth out any air bubbles. Make sure all edges are firmly in place and trim off any excess.
Preparing the plane
It is necessary to adhere non-woven wallpaper to a smooth, level surface. Concrete typically has a level surface already.
However, this does not imply that it is axis-centered and smooth:
- Immediately take the fishing line and stretch it along the diagonals of the plane. Here we will see deviations. If they are more than two cm, then you need to plaster the plane (see. Technology of plastering walls: how to do it right);
- If the deviations are less, then we simply putty the surface. After all, there are always sinks on concrete;
- Mix the finishing material, for this you should take a container without stiffeners. And dilute the composition in it;
- Take a wide spatula and apply a thin layer on the wall. Fill all the cavities in the concrete;
- After the solution has dried, it is passed along the plane with a construction mesh. To begin with, we take one with a large cross-section. After that we go through small. We must have a smooth and even surface;
- Now the plane is primed (see. Wallpaper primer: which one to choose and how to use). To do this, you should purchase a mixture of deep penetration.
Note: You need to complete the preparatory step for non-woven wallpaper. Ultimately, glue will not seep into concrete. Additionally, there won’t be any issues with this after putty is applied.
One aspect of preparation is marking. This will ultimately determine how the wallpaper stripes look and are shaped. The wallpaper must be removed from its level of fastening right away. Just use a nylon thread to break off the fastening line to accomplish this.
In order to glue the first strip, we also mark the vertically. In order to accomplish this, we draw a line and use a plumb line to verify its verticality.
Wallpaper preparation and gluing
The guidelines for this matter are straightforward; we will go over how to adhere non-woven wallpaper in more detail below:
- Prepare the glue in advance. There are instructions on the package for diluting it. The required proportions are written there. Also, after the glue has been infused, mix it thoroughly with your hands and at the same time knead all the lumps;
- Now cut the wallpaper. This is done to the desired size. Five cm should be added to the required length, they will be needed for proper trimming;
- After this, take the prepared glue and pour a little into a separate container. This will be our primer. Add water and make the composition liquid. It should be completely absorbed into the prepared surface. We apply it to the wall;
- Now take the cut sheet and apply glue to it;
- We glue the sheet along the previously determined markings. Usually, they are glued first from the corner, while a small part of it lies along the corner and goes to the other wall;
- The upper part is glued overlapping the baseboard, after gluing, the excess is trimmed;
- Now we glue around the entire perimeter. Where the wallpaper lies incorrectly and unevenly, it is difficult to fit the next strip to it. Then we glue the overlap and trim along the length;
| Step | Description |
| Prepare the Surface | Clean the concrete wall from dust, dirt, and any loose materials. Apply a primer to ensure better adhesion. |
| Measure and Cut | Measure the height of the wall and cut the wallpaper strips, leaving a little extra length at the top and bottom for adjustments. |
| Apply Adhesive | Spread adhesive evenly on the wall using a roller, covering an area slightly wider than the wallpaper strip. |
| Attach the Wallpaper | Align the top of the wallpaper with the ceiling and smooth it down, removing any air bubbles with a brush or roller. |
| Trim Excess | Once the wallpaper is securely in place, trim any excess at the top and bottom using a sharp knife. |
| Finish | Continue with the next strip, making sure the patterns match and edges align. Let it dry according to the adhesive"s instructions. |
Your walls can be transformed with non-woven wallpaper to give them a modern and fashionable look. To guarantee a seamless conclusion, preparation and following the correct procedures are crucial. The surface can be perfectly primed and cleaned to provide an excellent foundation for the wallpaper to stick to.
When applying the strips, it’s crucial to take your time and make sure they are all aligned and wrinkle- and bubble-free. You can achieve a professional look that will last for years by using the right adhesive and tools.
This is a very efficient and satisfying way to update a room or your entire house. You can have exquisitely decorated walls that improve the atmosphere of your room with the appropriate method.
Video on the topic
Wallpaper directly onto concrete without puttying (part 2)
How to glue non-woven wallpaper
How to properly glue non-woven wallpaper?
CONCRETE WALLPAPER. Modern solution
