Are you considering painting your walls a different color? Plasterboard covering them with a metal frame is a great do-it-yourself project that can completely change your area. This method adds an additional layer of soundproofing and insulation to your room while also improving its aesthetics. Furthermore, with the right tools and a little perseverance, even beginners can complete the project with ease.
Plasterboard is attached to a metal frame that is fastened to your current walls during the process. This method is preferred because it is easy to use and efficient. The plasterboard is firmly supported by the metal frame, which guarantees a smooth and level surface for your newly installed wall. You don’t need to hire a contractor to get results that look professional—all it takes is some careful planning and measurement.
We’ll take you step-by-step through the process of installing plasterboard on a metal frame in this tutorial, from assembling the framework to fastening the plasterboard panels. We’ll go over everything you need know, including typical pitfalls to avoid, to complete the task correctly. This do-it-yourself method will assist you in reaching your desired outcome whether you’re remodeling a single room or taking on a more extensive project.
Step | Description |
1 | Measure the walls where you"ll install the plasterboard. Make sure to get accurate dimensions to cut the plasterboard properly. |
2 | Install the metal frame. Attach vertical metal studs to the floor and ceiling, and add horizontal tracks to connect them. Make sure the frame is level and securely fixed. |
3 | Cut the plasterboard to fit the frame. Use a utility knife to score the plasterboard and then snap it along the cut. |
4 | Attach the plasterboard to the metal frame. Use screws to fix the plasterboard to the metal studs. Make sure the screws are countersunk and the board is flush with the frame. |
5 | Seal the joints between plasterboard sheets with joint tape and joint compound. Apply multiple layers of compound, sanding between each layer for a smooth finish. |
6 | Finish the surface by sanding it smooth once the joint compound is dry. You can then paint or decorate as desired. |
- Wall cladding with gypsum
- Features of cladding gypsum board walls on a metal frame: technology
- DIY metal frame assembly: installation
- GKL sheathing on profile
- Finishing
- Video on the topic
- video tutorials, types of jumpers for joining two sheets of drywall. Rigips.
- Interior partition made of drywall! In 1 day WITH YOUR OWN HANDS!
- Do-it-yourself wall cladding with drywall. THE WHOLE PROCESS!! Frame for drywall.
- Partition made of drywall. Video tutorial. Do it yourself. All stages
Wall cladding with gypsum
Navigating pages
Plasterboard sheets are used for insulating a room from heat and sound, covering communications, and creating uneven walls. Gypsum board walls that are extremely "cluttered" should only be clad with a metal frame; otherwise, the frameless approach is inappropriate. Additionally in other circumstances.
There are guidelines that must be followed when covering walls with gypsum boards, considering the subtle differences between the materials.
Features of cladding gypsum board walls on a metal frame: technology
In the following situations, plasterboard sheets are fastened to a metal frame:
- “Collapsed” wall – the curvature of the surface is more than 5 cm.
- Hiding communications – by creating a metal base, wiring, Internet cables, TV, pipes, hoods are hidden in it.
- Wet rooms – in such rooms the frameless method is not suitable because the sheets can peel off and become deformed.
- Insulation and soundproofing – heat-insulating, noise-absorbing materials are laid in the metal lathing. The room becomes neat, warm, quiet.
- The shelf life of a wall made of plasterboard on a metal base is longer than sheets glued with adhesive mortar.
Although making a metal lathe is more expensive, the finished product is better made, more resilient, and has a longer lifespan.
The following tasks are necessary for the technology to create a frame base:
- Surface preparation – it is necessary to prepare the walls for fixing the profiles, laying heat-insulating materials, wiring.
- Purchase of material and collection of the necessary tool. If there is no power tool, you can rent it.
- Marking is an important stage, where each line must be perfectly straight, each point must be in the right place.
- Fixing profiles – choosing fasteners, correct step-by-step installation of each guide and fastener.
- Checking the strength and evenness of the frame base.
- Fastening plasterboard – correct fixation of sheets.
- Finishing – reinforcing joints, priming, puttying.
- Finishing coating – this can be wallpaper, paint, tiles.
Step-by-step instructions are provided for every step; following them will help you avoid mistakes and future issues.
DIY metal frame assembly: installation
Take a few steps before beginning to install the metal lathing.
Work in preparation: cleaning the surface, gathering tools, and making material purchases.
In order to manipulate the surface, you’ll need:
- deep penetration primer and roller;
- reinforcing fiberglass mesh;
- plaster (gypsum-based);
- construction gun or heater;
- spatula;
- lime, copper sulfate.
Getting the surface ready. The previous layer has been removed from the walls:
- wallpaper – it must be removed to assess the rough base;
- paint – peeling paint is removed with a spatula;
- tiles – they are knocked off, there may be many cracks under them, a wet wall.
Dust and cobwebs are removed from the rough base. Check for chips, cracks, and holes. If there are cracks, they need to be sealed, or else they will get bigger over time. This is accomplished by using a spatula to clean the crack’s sides, slightly widening it. mesh and plaster reinforcement. Fiberglass mesh is used for these purposes. It will stop the crack from spreading. Plaster must be applied as a layer to cover the mesh after reinforcement. With holes, the same process is followed.
Damp walls need to be dried. Use a construction gun, a heater, or open the windows and doors to let some fresh air in (especially in dry, hot weather). Mold residue that has dried is then wiped off the wall. A lime and copper sulfate solution is applied to the wall. The fungus that is still on the surface is killed by this. dry once more. Applying a deep penetration primer to the wall is the last step. It will shield the surface from fungal growth and the regrowth of mold.
After finishing the task, the surface needs to thoroughly dry. You have twenty-four hours to do this.
You need the following tool to make a metal frame:
- Tape measure, square, marker – for marking.
- Scissors for metal – for cutting the profile into the required lengths.
- Perforator, screwdriver, hammer.
- profiles – NP (UW), PS (CW);
- direct hangers, crabs;
- GKL – gray, green (depending on the installation location);
- Insulation;
- serpyanka or Knauf paper tape;
- putty for joints;
- primer;
- dowel-nails 6/40, 6/60;
- self-tapping screws for metal frame 13, 16 mm;
- self-tapping screws for plasterboard 3.5×25.
You must locate the wall’s largest protrusion in order to mark it. Use a plumb line for this. On the walls next to you, mark the points at the top and bottom. Along the indicated floor, ceiling, and adjacent wall locations, draw a square. Along these lines, the guide profile will be fixed.
After that, take a 40-centimeter step back from the wall’s edge and draw a vertical line. These are spaced 40 centimeters apart along the wall. The transverse ones are necessary for the frame’s strength. Every 40 cm, lines are positioned horizontally for them. One obtains cells.
It is necessary to use a level to ensure that all unmarked lines are level.
- Creating a metal frame
The following tasks are completed in order to fix the profiles in the proper order:
- First, NP (UW) is fastened along a quadrangle on semi-adjacent walls. Dowel-nails are used for this.
- Straight hangers are fastened on the walls along vertical lines at a distance of 30 cm. Fixation is carried out with dowel-nails.
- The rack profile is inserted into the guide and fastened with self-tapping screws 13. Along the standing line is fixed to straight suspensions.
It is revealed to be a metal sheath. Stiffening ribs are designed to stiffen the frame if the equipment or objects are intended to be hung on the wall. The rack profile is divided into segments, which are then fixed horizontally between the vertical elements. Crabs are utilized in the process of fixing to the vertical PS.
Every metal structure is examined for stiffness, evenness, and strength.
Insulation, cables, and wiring are installed within the sheathing.
Plasterboard can give your walls a new look, and mounting it on a metal frame is an easy do-it-yourself project that can update any space. This tutorial will walk you through every step of plasterboard application using a metal profile, from surface preparation and frame assembly to plasterboard sheet attachment and surface finishing. Whether you’re an experienced do-it-yourselfer or a novice, we’ll simplify the procedure into simple steps so you can accomplish a polished outcome on your own.
GKL sheathing on profile
This is the sequence in which the frame base sheathing is completed.
Whole sheets are fastened starting from the center of the wall or from the corner, backing up to 5 mm. Self-tapping screws are used to secure entire sheets to the profile so that the horizontal joints do not line up. In other words, one sheet is fastened from the floor, and another from the ceiling.
Measurements are taken, plasterboard pieces are cut out, and the windows are sewn up. If two sheets are intended, the second layer must be fastened with 2.5×35 self-tapping screws so that the joints do not line up with the first layer.
All joints are strengthened with joint filler and serpyanka (paper tape) after the frame has been sheathed. Putty is utilized to seal the fastening points.
Finishing
Once the putty has dried in all the joints, wipe it down and remove any excess. Primers are applied to the whole surface of the plasterboard. Putty a thin layer on top of that. It has to be based on gypsum.
Putty should be applied thinly—1-2 mm—and allowed to dry. After that, use sandpaper to rub away any extra stones or stripes. When the surface is smooth, more finishing can be applied.
Prime the surface before completing it.
The finishing is done in the style that is preferred. This could be gypsum "brick," tiling, decorative plaster, or light-colored wallpaper. Anchor wedges can be used to hang bookcases or TVs on the wall if the frame base was made with stiffeners.
A universal building material is drywall. It is used to create shelves and niches, with pipes and communications hidden underneath. By creating a metal sheathing and employing a frameless technique, the wall is aligned with sheets of gypsum plasterboard. You will need a set of power tools and meticulous work to face the wall with "dry plaster."
Plasterboard covering your walls with a metal frame is a great do-it-yourself project that can completely change your room. You can achieve a smooth, polished finish that enhances insulation and soundproofing in your home while also looking fantastic by following the instructions provided in this guide.
Recall that preparation is essential. The difference can be enormous if the plasterboard is measured and cut precisely, your metal frame is firmly fastened, and the appropriate tools and materials are used. Don’t rush the process; instead, take your time at each step. You can be sure that your wall decoration is both aesthetically pleasing and long-lasting by taking this meticulous approach.
Plasterboard installation on a metal frame can be a rewarding project if you have a little patience and pay attention to detail. It lets you add flair to your room and improve the way your walls look overall. Success is just around the corner, so enjoy the process and don’t be afraid to ask for assistance or advice when you need it!