Ceramic tiles of drywall: we do correctly

Want to update your walls with something new and fashionable? Ceramic tiles are a great option for drywall because they are long-lasting and visually appealing in any space. But a little bit of expertise is needed to do it correctly. We’ll walk you through each crucial step in this guide to make sure your ceramic tile installation on drywall goes smoothly and successfully.

First things first: getting ready is essential. It’s important to properly prepare your drywall surface before you begin. This entails checking that it’s dry, clean, and free of any flaws that might compromise the adhesive. An impeccable tile installation is predicated on proper surface preparation.

We’ll then look at the best techniques for tiling ceramic tiles onto drywall. A professional finish is the result of a meticulous process that begins with selecting the appropriate adhesive and ends with evenly placing the tiles. We’ll also go over some typical traps to watch out for so you can avoid any potential problems.

A stunning and long-lasting ceramic tile installation can be accomplished with a little perseverance and attention to detail. Together, we can confidently begin your project by delving into the specifics!

It’s essential to follow the correct procedures when installing ceramic tiles on drywall to guarantee a smooth, long-lasting finish. Start by carefully prepping the wall surface, applying a premium adhesive, and making sure the tiles are spaced uniformly. To stop moisture damage, pay attention to grout lines and seal the grout. You can improve the aesthetics and usability of your space with a professional-looking finish that requires the right planning and execution.

The process of finishes

The process of lining drywall walls with ceramic tiles starts with carefully choosing the sheets and the fasteners for them. The tiles will not lie in the same plane if this is done poorly and the wall is uneven, which will draw attention right away.

Rules for finishing with plasterboard under tiles

Ceramic tile facing on plasterboard requires a surface that has been properly prepared. If you don’t fulfill certain requirements, the project won’t look good and won’t last very long. Success starts with a surface that is well-prepared:

  • First of all, make the correct markings. The geometry of the finish will completely depend on this.
    If on plasterboard this may not be noticeable, then the tile has edges and this is visible. And if the seam does not match, then this will immediately catch the eye;
  • Facing walls from plasterboard with ceramic tiles must be done on the right material. After all, if you attach ordinary sheets in the bathroom, then over time they will gain moisture and warp and this will spoil the entire surface.
    Therefore, for rooms with high humidity, it is worth choosing a moisture-resistant material.
  • The frame for the plasterboard should be attached in one plane. Otherwise, the material will simply repeat its incorrect contour.
    Therefore, after completing the frame strapping, you should stretch the fishing line diagonally and adjust the height of the cross-section fastening using spacers. And this should be done qualitatively;
  • Do not fasten the sheets tightly to the surface of the walls. Make a gap of about one cm. This will save you from trouble when the material expands.

Note: Make sure the base plane is ready before attaching the frame. Apply antiseptics to the surface. If fungus develops later, on the other hand, you will have to take everything apart.

Surface preparation

We have premium plasterboard attached; however, in order to ensure correct fastening, the surface needs to be properly prepared. This is the first step in facing walls with ceramic tiles on plasterboard. Correct fastening is impossible without superior processing:

  • Let"s inspect the planes. We check the layer of solution that will need to be applied.
    To do this, you should pull the line diagonally across the plane and you will immediately see how much solution will need to be applied;
  • Determining the number of seams. We need to putty the surface and place perforated tape on the joints. It will strengthen the seam and make it better;

  • Mix the solution. To do this, a dry mixture is most often used, which should be passed through a sieve to separate out all the debris and crush the lumps;
  • After this, pour it into a container for mixing the solution. To do this, it is best to use containers without stiffeners on the edges and bottom. Then the kneading can be done with the highest quality;
  • Pour in the dry mixture and add water. Now we need to mix it well.
    The mass should be completely homogeneous and have the appearance of thick sour cream. For this, it is best to use a drill with an attachment.
    Stir. If necessary, then add water. The solution is ready;
  • Now we need to level the plane. After all, the solution is not applied to the tile in a thick layer.
    Therefore, we are not interested in roughness. We need a flat plane.
    For this, take a wide spatula and apply the solution to the plane. We are not interested in small sinks. We need to level the plane as a whole;
  • At the joints of the sheets, we put a perforated tape and putty on it. We wait until the surface is completely dry;

  • We lightly go over the surface with a construction mesh and knock down the unevenness;
  • Now we apply a layer of primer to the plane. For this, we use a brush or a sprayer. Preference should be given to a deep penetration liquid.

Tiling

It’s not so easy to face walls with ceramic tiles on plasterboard; you have to consider the room’s dimensions as well as the ceiling height. Ultimately, one solution won’t be effective everywhere.

For a small room

This is a good choice for compact spaces. For instance, in a small-family apartment or one from the Khrushchev era. Here, we make our selections based on the guiding idea:

  • The tiles should not be large or mosaic;
  • In terms of shades, preference should be given to cold and light tones;
  • In terms of surface type, gloss is best;
  • It is best to choose a horizontal method for laying;
  • If you plan to use a pattern or frieze, then it is better to place it along the wall.

If the ceiling is not high

Here, we need to enlarge the space, if only temporarily:

  • We use a vertical method for laying tiles;
  • We also attach the ornament or frieze in a vertical position;
  • For a corner bath, it is best to use vertical columns;
  • If we use decorative inserts, then we place them at eye level or higher.
Step Details
1. Preparation Start by cleaning the drywall surface. Ensure it’s smooth and dry for the best adhesion.
2. Layout Plan the tile layout before applying adhesive. This helps avoid awkward cuts and ensures a balanced look.
3. Adhesive Apply a suitable tile adhesive to the drywall. Use a notched trowel for an even spread.
4. Tiling Press the tiles into the adhesive, following your planned layout. Use spacers to maintain consistent gaps.
5. Cutting Cut tiles as needed to fit edges and corners. Use a tile cutter or a utility knife for clean cuts.
6. Grouting Once the adhesive dries, apply grout between the tiles. Wipe off excess grout with a damp sponge.
7. Sealing Apply a sealer if needed, especially in moisture-prone areas, to protect the grout and tiles.

Selecting the ideal ceramic tiles for drywall can completely change the appearance of your room and give it a modern, chic look. When done correctly, it guarantees durability and ease of maintenance in addition to improving the aesthetic appeal. To prevent any problems with tile adhesion, begin by thoroughly cleaning, drying, and smoothing the drywall surface.

It’s important to choose the proper tile and adhesive. Use an adhesive that works well with both the tiles and the drywall, and choose tiles that complement the design and function of the space. For a safe and durable outcome, install according to the manufacturer’s instructions.

After the tiles are installed, they will remain beautiful and protected with the right grout and sealing. Your tiled walls’ functionality and appearance will last longer with regular maintenance. You can get a gorgeously polished look that withstands normal wear and tear by following these steps.

Video on the topic

Laying CERAMIC TILES on walls assembling BOXES

OPTIONS for laying tiles in 90° CORNERS TILES laying OUTER CORNER for tiles in the BATHROOM Laying VIDEO

Corner made of ceramic tiles. Do-it-yourself tiling of the box. BUILDING FOR OURSELVES

How to properly lay large-format porcelain tiles 60*120 on walls.Laying large-format tiles

Laying large-format porcelain tiles / Installation of large tiles on walls

How to lay tiles on plasterboard walls? Size 30×90 cm.

How to install corners on tiles with your own hands

What interior style do you like the most?
Share to friends
Veronica Gerasimova

Interior designer, author of books on the design of residential premises. I will help you make your home not only functional, but also beautiful.

Rate author
Vash-Variant.com
Add a comment